自动上料机吸料风机 分离式吸料机配套风机

Automatic feeder suction fan, separable suction fan for feeder

自动上料吸料风机性能特点：

1. 超型 , 无噪音 : 马达直接运转，在通过加上体式的销音设施，改进了高压风机噪音的现像 , 从而达到的效果。

2. 可靠性高当使用情况变化时，机器仍可安全运转。除了叶轮之外，高压鼓风机没有其他动作，因此可靠性之高几乎免维修。使用*且散热良精密外侧轴承，因此它具有下列优点：高压缩比；轴承运转温度低；润滑油脂寿命长；免保养。

3. 安装容易 配备齐全，可随时安装与使用，供压缩空气或用于抽真空，也可任意安装于水平或垂直的方向。

4. 无油无污染 叶轮旋转时，不与任何部分零件接触，免润滑，因此可保证无污染。

5. 高品质 经过20 年的业制造经验，精密机械设计加上慎重电机配合标准仪器测试，使用所有零件均能达到高品质要求，运用标准 ip54 ， F 级马达效率高，故障极少，马达与鼓风机之间有轴封分试，预防异物进入。同时为确保功能效果，每台鼓风机在出厂前均经过严格测试。

Automatic feeding machine suction fanPerformance characteristics:

1. Super size, no noise: The motor is directly driven, and the noise of the high-pressure blower is improved by adding a body-type silencer, thus achieving the desired effect.

2. High reliability: the machine can still operate safely when the operating conditions change. In addition to the impeller, the high-pressure blower has no other action, so its reliability is almost maintenance-free. It has the following advantages due to the use of * and good heat dissipation precision outer bearing: high compression ratio; The bearing operation temperature is low; Lubricating grease has a long service life; No maintenance required.

3. Easy to install, fully equipped, can be installed and used at any time, for compressed air or vacuum suction, can also be arbitrarily installed in the horizontal or vertical direction.

4. Oil-free and pollution-free When the impeller rotates, it does not come into contact with any part of the machine, so it is lubricant-free and pollution-proof.

5. High quality After 20 years of industry manufacturing experience, precision mechanical design combined with careful motor matching and standard instrument testing, All parts can meet the high-quality requirements, using standard IP54, F-class motor with high efficiency, very few failures, there is a shaft seal between the motor and the blower to prevent foreign objects from entering. At the same time, in order to ensure the function effect, each blower is strictly tested before leaving the factory.

自动上料吸料风机各行业应用激光雕刻设备、燃烧降氧机、卷烟滤嘴成型机、雾化干燥机、、丝网印刷机、照相制版机、注塑机、自动上料烘干机、液体灌装机、粉末灌装机、电焊设备、电影机械、纸张运送、干洗衣服、清洁用途、空气除尘、干瓶除水、气体传送、送料、吸料、物料收集、中央集尘环境保护、丝网印刷、电镀行业、除尘集尘、食品机械、包装设备、灌装行业、玻璃制品、气流输送、水处理曝气等相关行业和机械。

Automatic feeding machine suction fanLaser engraving equipment, combustion oxygen reduction machine, Cigarette filter mouthpiece forming machine, atomization drying machine, screen printing machine, photographic printing machine, injection molding machine, automatic feeding drying machine, liquid filling machine, powder filling machine, electric welding equipment, film machinery, paper transportation, dry cleaning clothes, cleaning purposes, Air dust removal, dry bottle water removal, gas transmission, feeding, suction, material collection, central dust collection, environmental protection, screen printing, electroplating industry, dust collection, food machinery, packaging equipment, filling industry, glass products, air flow transmission, water treatment aeration and other related industries and machinery.

自动上料吸料风机操作及维护：

1.安装竣工后的鼓风机在启动前应行手动转动，检查有无异常碰撞与摩擦，电动机的旋向是否正确，进出口阀门是否在小流量状态。

2.风机运行时应注意风机和电机内部有无异常声响，漏油，异常的振动或轴承温升过高，电机电流过，地脚松动等不正常现象，并及时排除。

3.新风机使用5000小时后要更换轴承油脂。

4.检修：机壳检修时先松开水平中分面上螺钉，打开上半机壳和两侧轴承箱上盖，取出转子即可对转子或机壳进行维修。检修时应特别注意叶轮叶片是否断裂，有无裂纹，主轴是否弯曲。装拆上班机壳前，必须谨慎避免装拆过程中因上半机壳摆动而损坏转子。

5.风机出厂时货用户停机期间均应将风机进出口盖，以防止杂物落入风机内腔造成事故。

6.风机每工作半年需检修次，清楚风机流道内积尘和油污。

Automatic feeding machine suction fanOperation and maintenance:

1. Before the blower is started, it should be manually rotated after the installation is completed to check if there are any abnormal collisions and friction, whether the direction of the motor is correct, and whether the inlet and outlet valves are in the small flow state.

2. When the fan is running, attention should be paid to whether there are any abnormal sounds, oil leakage, abnormal vibration or excessive bearing temperature rise in the fan and motor, excessive motor current, loose foot, and other abnormal phenomena, and they should be eliminated in time.

3. The bearing grease should be replaced after 5000 hours of use.

4. Inspection: When inspecting the casing, first loosen the screw on the horizontal center plane, open the upper half of the casing and the cover of the two sides of the bearing box, and take out the rotor to repair the rotor or the casing. During maintenance, special attention should be paid to whether the blade of the impeller is broken, whether there are cracks, and whether the main shaft is bent. Before disassembling and reassembling the working machine casing, it is necessary to be cautious and avoid damaging the rotor during the disassembly and reassembly process due to the movement of the upper casing.

5. The inlet and outlet covers of the fan should be closed when the fan is not in use to prevent debris from falling into the fan's internal cavity and causing an accident.

6. The fan should be inspected once every six months to clear dust and oil in the fan duct.

自动上料吸料风机我们的服务理念：

1.TWYX售前服务：阜风公司为您提供详细的风机技术参数，给予您选出更合适您使用的风机。

2.TWYX售中服务：我公司专职服务人员和您一起跟踪货物，直到货物安全到达您的手里。

3.TWYX售后服务：公司销售人员为您简单了解讲诉风机的原理，及注意事项。

4.TWYX质量保证：我们全系列产品12个月质量保证。

5.如果有不明白的操作可咨询我公司专业的技术专员，为您讲解操作方案。

6.TWYX公司将提供耐心、友好、热情的支持，可靠保障客户安全使用及运营。

Automatic feeding machine suction fanOur service philosophy:

1. TWYX pre-sales service: Furong Company provides you with detailed fan technical parameters, giving you to choose the fan more suitable for your use.

2. TWYX sales service: Our company's dedicated service personnel will follow up with you until the goods arrive safely in your hands.

3. TWYX after-sales service: the company sales staff will explain the principle and precautions of the fan to you briefly.

4. TWYX Quality Assurance: 12 months quality assurance for all our products.

5. If there is any operation that you do not understand, you can consult our company's professional technical specialist to explain the operation plan for you.

6. TWYX will provide patient, friendly, and enthusiastic support to ensure the safe use and operation of customers.

自动上料机吸料风机 分离式吸料机配套风机

Automatic feeder suction fan, separable suction fan for feeder